 |
 |
 |
| |
 |
 |
| |
*FREE ESTIMATES
*No Adhesives
*N0 Holes In Your Roof *References
Available
*Satisfaction Guaranteed
|
 |
| |
| |
 |
| |
 |
| |
 |
 |
 |
 |
 |
| Click
For Info |
| |
| Our NEW
BIG MOUTH™ can be installed on existing gutters and downspouts
or you can upgrade them with these non clogging gutter outlets and
create a maintenance free gutter system to help protect your home
from the elements. |
|
|
SP |
|
|
| |
 |
 |
 |
 |
 |
|
 |
|
| |
|
|
Did you know that moss, mildew, algae and fungus can discolor
your roof, feed on the organic material in your shingles
and eventually destroy them? You can positively prevent
such damage and insure the full life of your valuable roof
for $150 or less with our Shingle Shield products.
The Shingle Shield 3 foot zinc strips are precision engineered
to provide environmentally safe (EPA approved), long term
(20 year warranty) roof protection from fungus, moss, mildew
or algae attack. One-year money-back satisfaction guarantee.Ý
By installing one row at or near the roof ridge line, you
protect your entire roof. Every time it rains, Shingle Shield
goes to work releasing invisible, safe fungi static compounds
of zinc oxide which inhibit the growth of fungus, moss,
mildew and algae on your roof and keep it looking beautiful.
And the best part, it goes up quickly, safely and lasts
the lifetime of most roof! Great for preventing problems
on your new roof or on your existing stained and
discolored roof after you have cleaned it with Shingle
Shield Roof and Deck Cleaner. Order enough to do a great
job of brighteningÝ up your decks too!
|
| Installation
Instructions |
| Shingle Shield should be installed in a
straight line under the first row of shingles below the
ridge. Leave a 1/8" gap between each piece, or simply
overlap the pieces - this provides for thermal expansion
of zine, which could be take place under the most severe
high temperature conditions
Material Required:
Hammer
Quality Roofing Nails Neo-prene
Washered Roofing Nails
(Double hot-dipped galvanized
) (Double hot-dipped galvanized)
for asphalt and fiberglass
shingle roofs for cedar wood roofs
|
| |
 |
 |
1.) Beginning from either end of the roof peak install
a continous single row under the first available course
of shingles below the ridge line. Allow for thermal expansion
by leaving 1/8" (0.3 cm) pap between each section, or
slightly overlap sections. Slide Shingle Shield up under
the shingle until its built-in alignment guide butts against
the edge of the shingle. |
| |
|
|
 |
|
2.) Once aligned, raise shingle tab, locate the pre-punched
hole and nail into place using a high quality hot-dipped
galvanized roofing nail. Note: A dab of roofing cement
over the nail head will insure a watertight seal (wood
roofs should use a neoprene washer head nail). |
| |
|
|
Shingle Shield is designed to be installed
on a new or existing roof. Roof must be cleaned
with shingle shield Roof & Deck Cleaner to remove
any existing algae, fungus, and/ or moss prior to installation
of Shingle Shield zinc strips. Shingle Shield will
last the life of the roof, and may be reused. Will
not rust.
IMPORTANT! Do not attempt
to install this product in rain, when roof is wet, or
if a lightning storm is imminent. Use care when raising
shingles - in warm weather, they may be tacky and stick
together where overlap occurs; in cold weather, they
may be brittle and subject to cracking or breaking.
|
| |
| Feel
free to
for more information on Metro’s Smart Roofs for
Smart People™. |
|
| |
| |
| |
|
|
| |
| |
| |
| |
|
|
